{"id":3243,"date":"2026-11-19T08:00:00","date_gmt":"2026-11-19T08:00:00","guid":{"rendered":"https:\/\/kurtfoundry.com\/?p=3243"},"modified":"2026-11-07T04:48:38","modified_gmt":"2026-11-07T04:48:38","slug":"cast-counterweight-weight-tolerance","status":"publish","type":"post","link":"https:\/\/kurtfoundry.com\/fr\/blog\/cast-counterweight-weight-tolerance\/","title":{"rendered":"Quelle tol\u00e9rance de poids sp\u00e9cifier sur un contrepoids moul\u00e9"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\">Specify the tolerance as a percentage of a stated nominal weight, and start at about \u00b15% on a 100\u2013400 kg (220\u2013880 lb) <a href=\"https:\/\/kurtfoundry.com\/product\/custom-counterweights\/\">sand cast counterweight<\/a>. Go tighter only when the machine&#8217;s own limit requires it. We found no standard that sets a weight tolerance for counterweights, so the \u00b15% comes from general casting tables.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The \u00b15% assumes a cast weight fitted to a machine, where the weight is the working figure. <a href=\"https:\/\/kurtfoundry.com\/product\/calibration-test-weights\/\">Calibration and test weights<\/a> belong to a far tighter scale.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The job can change the direction of the limit as well as its size, because each machine depends on the weight in a different way:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Cranes and other machines rated on a load chart<\/strong>: write the limit one-sided, plus only and minus 0, because a light piece leaves the machine short of what its chart assumes.<\/li>\n\n\n\n<li><strong>Traction elevators<\/strong>: work from the overbalance range on the data plate, which limits the stack in both directions.<\/li>\n\n\n\n<li><strong>Tractor ballast for EU type approval<\/strong>: keep the marked mass accurate to \u00b15%, the figure the regulation sets.<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">What Weight Tolerance a Sand Cast Counterweight Can Hold<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">A sand cast counterweight of 100\u2013400 kg (220\u2013880 lb) can be held to about \u00b15%, and closer on a molding machine in long runs. The figures below come from Russian and Chinese casting standards, the only mass tolerance tables we could read.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Both standards state a total band, so a 10% band means \u00b15%.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">GOST R 53464-2009, the Russian standard in force, recommends classes 8 to 15 for as-cast ferrous parts of 100\u20131,000 kg in green sand at 3.5\u20134.5% moisture or liquid self-hardening mixes. At 100\u2013400 kg, those classes run from a 3.2% band (\u00b11.6%) to a 32% band (\u00b116%). The low end is for simple compact castings in automated mass production, and the high end is for complex large one-offs.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A counterweight is simple and compact but rarely made in automated mass production, so the standard names no single class for it. GOST class 11, near the middle, is a 10% band (\u00b15%) at 100\u2013400 kg. Outside that range, start from the same class: \u00b16% at 40\u2013100 kg, \u00b14% at 400\u20131,000 kg and \u00b13.2% at 1,000\u20134,000 kg.<\/p>\n\n\n\n<div data-chart-block=\"grouped_bar\" class=\"nm-chart\" role=\"figure\" aria-label=\"The same class allows a larger percentage on a lighter casting \u2014 Casting mass tolerance by nominal mass, GOST R 53464-2009 Table 4 (total band, % of nominal mass)\"><style>.nm-chart { margin:2rem 0; padding:1.25rem 1.4rem; background:var(--nm-paper,#f7f8fa); border:1px solid var(--nm-line,#dfe4ea); border-radius:12px; color:var(--nm-ink,#1c2e4a); font-family:inherit; } .nm-chart .nm-title { font-size:1.05rem; font-weight:700; line-height:1.3; margin:0 0 .25rem; } .nm-chart .nm-subtitle { font-size:.9rem; line-height:1.45; margin:0 0 1.1rem; color:var(--nm-muted,#6b7a8c); } .nm-chart .nm-rows { display:flex; flex-direction:column; gap:.85rem; } .nm-chart .nm-row { display:grid; grid-template-columns:minmax(80px,22%) 1fr max-content; align-items:center; gap:.75rem; } .nm-chart .nm-rowlabel { font-size:.9rem; line-height:1.3; overflow-wrap:anywhere; color:var(--nm-label,#3c4a60); } .nm-chart .nm-track { position:relative; height:1.5rem; border-radius:4px; background:var(--nm-track,#e3e7ed); } .nm-chart .nm-bar { position:absolute; top:0; height:100%; border-radius:4px; background:var(--nm-bar,#2b4d76); } .nm-chart .nm-zero { position:absolute; top:-.3rem; bottom:-.3rem; width:2px; background:var(--nm-label,#3c4a60); opacity:.55; } .nm-chart .nm-refband { position:absolute; top:-.2rem; bottom:-.2rem; border-radius:3px; background:var(--nm-accent,#c8611a); opacity:.22; } .nm-chart .nm-refline { position:absolute; top:-.3rem; bottom:-.3rem; width:3px; background:var(--nm-accent,#c8611a); opacity:.8; } .nm-chart .nm-sw-ref { background:var(--nm-accent,#c8611a); opacity:.45; } .nm-chart .nm-value { font-size:.9rem; font-weight:700; text-align:right; white-space:nowrap; color:var(--nm-accent,#c8611a); } .nm-chart .nm-grows { display:flex; flex-direction:column; gap:1.1rem; } .nm-chart .nm-grow { display:grid; grid-template-columns:minmax(80px,22%) 1fr; align-items:center; gap:.75rem; } .nm-chart .nm-gtracks { display:flex; flex-direction:column; gap:.3rem; } .nm-chart .nm-gtrack { display:grid; grid-template-columns:1fr max-content; align-items:center; gap:.75rem; } .nm-chart .nm-gtrack .nm-track { height:1rem; } .nm-chart .nm-gtrack .nm-value { font-size:.82rem; } .nm-chart .nm-stacktrack { display:flex; height:2rem; border-radius:5px; overflow:hidden; } .nm-chart .nm-seg { height:100%; } .nm-chart .nm-legend { display:flex; flex-wrap:wrap; gap:.55rem 1.5rem; margin-top:1rem; } .nm-chart .nm-legrow { display:flex; align-items:center; gap:.5rem; font-size:.9rem; } .nm-chart .nm-swatch { width:.8rem; height:.8rem; border-radius:2px; flex:none; } .nm-chart .nm-legval { font-weight:700; white-space:nowrap; color:var(--nm-accent,#c8611a); } .nm-chart .nm-leglabel { color:var(--nm-label,#3c4a60); } .nm-chart .nm-source { font-size:.78rem; letter-spacing:.02em; margin-top:1.1rem; color:var(--nm-muted,#6b7a8c); } .nm-chart .nm-axis { display:flex; justify-content:space-between; margin:.5rem 3.4rem 0 calc(22% + .75rem + 3.4rem); font-size:.72rem; color:var(--nm-muted,#6b7a8c); } .nm-chart .nm-tick { flex:0 0 auto; } .nm-chart .nm-axis-log { position:relative; display:block; height:1rem; } .nm-chart .nm-tick-abs { position:absolute; transform:translateX(-50%); white-space:nowrap; } .nm-chart .nm-dbrow { display:grid; grid-template-columns:minmax(80px,22%) 1fr; align-items:center; gap:.75rem; } \/* The row's extreme values sit AT 0% and 100% of the track, and their labels hang outside those points \u2014 so the track cannot span the full row or the widest label overflows the card (shipped 2026-08-02: \"200 %\" clipped off the right edge). Reserve a gutter on both sides instead of shrinking the data. *\/ .nm-chart .nm-dbtrack { position:relative; height:2.1rem; margin:0 3.4rem; } .nm-chart .nm-dbline { position:absolute; top:50%; height:3px; margin-top:-1.5px; border-radius:2px; background:var(--nm-track,#e3e7ed); } .nm-chart .nm-dot { position:absolute; top:50%; width:.72rem; height:.72rem; margin:-.36rem 0 0 -.36rem; border-radius:50%; } .nm-chart .nm-dot-a { background:var(--nm-bar-a,#6f89a8); } .nm-chart .nm-dot-b { background:var(--nm-accent,#c8611a); } .nm-chart .nm-dbval { position:absolute; top:50%; font-size:.78rem; font-weight:700; white-space:nowrap; transform:translateY(-50%); } .nm-chart .nm-dbval-a { color:var(--nm-label,#3c4a60); } .nm-chart .nm-dbval-b { color:var(--nm-accent,#c8611a); } .nm-chart .nm-dbval-left { margin-left:-.75rem; transform:translate(-100%,-50%); } .nm-chart .nm-dbval-right { margin-left:.75rem; } .nm-chart .nm-sw-a { background:var(--nm-bar-a,#6f89a8); } .nm-chart .nm-sw-b { background:var(--nm-accent,#c8611a); } .nm-chart .nm-donutwrap { display:flex; flex-wrap:wrap; align-items:center; gap:1.5rem 2rem; } .nm-chart .nm-donut { position:relative; flex:0 0 auto; width:min(11rem,42vw); } .nm-chart .nm-donut svg { display:block; width:100%; height:auto; transform:rotate(0deg); } .nm-chart .nm-center { position:absolute; inset:0; display:flex; flex-direction:column; align-items:center; justify-content:center; text-align:center; pointer-events:none; } .nm-chart .nm-centerval { font-size:1.7rem; font-weight:800; line-height:1; color:var(--nm-ink,#1c2e4a); } .nm-chart .nm-centerlab { font-size:.75rem; margin-top:.25rem; color:var(--nm-muted,#6b7a8c); } .nm-chart .nm-donutside { flex:1 1 13rem; min-width:12rem; display:flex; flex-direction:column; gap:.55rem; } .nm-chart .nm-legdesc { color:var(--nm-muted,#6b7a8c); } .nm-chart .nm-note { margin-top:.5rem; font-size:.88rem; line-height:1.5; color:var(--nm-label,#3c4a60); } @media (max-width:640px) { .nm-chart .nm-row { grid-template-columns:1fr max-content; grid-template-areas:\"lab val\" \"track track\"; row-gap:.35rem; } .nm-chart .nm-rowlabel { grid-area:lab; } .nm-chart .nm-value { grid-area:val; } .nm-chart .nm-track { grid-area:track; } \/* The three area names above are hbar's; a grouped row's label and per-series tracks must not inherit them or the values vanish and the label drops below. *\/ .nm-chart .nm-grow { grid-template-columns:1fr; row-gap:.35rem; } .nm-chart .nm-grow .nm-rowlabel { grid-area:auto; } .nm-chart .nm-gtrack .nm-track, .nm-chart .nm-gtrack .nm-value { grid-area:auto; } .nm-chart .nm-dbrow { grid-template-columns:1fr; row-gap:.1rem; } .nm-chart .nm-dbtrack { margin:0 2.8rem; } .nm-chart .nm-axis { margin:.5rem 2.8rem 0 2.8rem; } .nm-chart .nm-donut { width:min(9rem,46vw); margin:0 auto; } }<\/style><div class=\"nm-subtitle\">Casting mass tolerance by nominal mass, GOST R 53464-2009 Table 4 (total band, % of nominal mass)<\/div><div class=\"nm-grows\"><div class=\"nm-grow\"><div class=\"nm-rowlabel\">40\u2013100 kg<\/div><div class=\"nm-gtracks\"><div class=\"nm-gtrack\"><div class=\"nm-track\"><div class=\"nm-bar\" style=\"left:0.00%;width:33.33%;background:#2b4d76\"><\/div><\/div><div class=\"nm-value\">4 %<\/div><\/div><div class=\"nm-gtrack\"><div class=\"nm-track\"><div class=\"nm-bar\" style=\"left:0.00%;width:100.00%;background:#c8611a\"><\/div><\/div><div class=\"nm-value\">12 %<\/div><\/div><\/div><\/div><div class=\"nm-grow\"><div class=\"nm-rowlabel\">100\u2013400 kg<\/div><div class=\"nm-gtracks\"><div class=\"nm-gtrack\"><div class=\"nm-track\"><div class=\"nm-bar\" style=\"left:0.00%;width:26.67%;background:#2b4d76\"><\/div><\/div><div class=\"nm-value\">3.2 %<\/div><\/div><div class=\"nm-gtrack\"><div class=\"nm-track\"><div class=\"nm-bar\" style=\"left:0.00%;width:83.33%;background:#c8611a\"><\/div><\/div><div class=\"nm-value\">10 %<\/div><\/div><\/div><\/div><div class=\"nm-grow\"><div class=\"nm-rowlabel\">400\u20131,000 kg<\/div><div class=\"nm-gtracks\"><div class=\"nm-gtrack\"><div class=\"nm-track\"><div class=\"nm-bar\" style=\"left:0.00%;width:20.00%;background:#2b4d76\"><\/div><\/div><div class=\"nm-value\">2.4 %<\/div><\/div><div class=\"nm-gtrack\"><div class=\"nm-track\"><div class=\"nm-bar\" style=\"left:0.00%;width:66.67%;background:#c8611a\"><\/div><\/div><div class=\"nm-value\">8 %<\/div><\/div><\/div><\/div><div class=\"nm-grow\"><div class=\"nm-rowlabel\">1,000\u20134,000 kg<\/div><div class=\"nm-gtracks\"><div class=\"nm-gtrack\"><div class=\"nm-track\"><div class=\"nm-bar\" style=\"left:0.00%;width:16.67%;background:#2b4d76\"><\/div><\/div><div class=\"nm-value\">2 %<\/div><\/div><div class=\"nm-gtrack\"><div class=\"nm-track\"><div class=\"nm-bar\" style=\"left:0.00%;width:53.33%;background:#c8611a\"><\/div><\/div><div class=\"nm-value\">6.4 %<\/div><\/div><\/div><\/div><\/div><div class=\"nm-legend\"><div class=\"nm-legrow\"><span class=\"nm-swatch\" style=\"background:#2b4d76\"><\/span><span class=\"nm-leglabel\">Class 8<\/span><\/div><div class=\"nm-legrow\"><span class=\"nm-swatch\" style=\"background:#c8611a\"><\/span><span class=\"nm-leglabel\">Class 11<\/span><\/div><\/div><\/div><!-- \/chart -->\n\n\n\n<p class=\"wp-block-paragraph\">China&#8217;s GB\/T 11351-89 splits the same question by process. For gray iron at 100\u2013400 kg, GB\/T 11351-89 gives about \u00b12.5% to \u00b14% for machine or shell molding in large batches. For gray iron at the same weight in <a href=\"https:\/\/kurtfoundry.com\/blog\/resin-sand-casting\/\">self-hardening sand<\/a> in small batches, GB\/T 11351-89 gives about \u00b15% to \u00b17%. That edition is withdrawn and the 2017 edition changed the values, so use the 1989 figures as a scale only.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How to Set the Tolerance From the Counterweight&#8217;s Job<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Find the check that depends on the weight, and work out how far the weight can move before that check fails. We found no published rule that turns a job into a percentage, so the number has to come from your own machine&#8217;s data.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Run the check at the lightest and the heaviest weight you could accept. The largest deviation that still passes is your limit. Convert it to a percentage of nominal weight:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Tolerance (%) = allowable weight deviation \u00f7 nominal weight \u00d7 100<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Compare the result with the casting figures above. If your number is looser than what the process holds, write your number. If it is tighter, every piece has to be weighed and sorted. Settle that with the foundry before the pattern is built.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Crane Counterweights<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">On a <a href=\"https:\/\/kurtfoundry.com\/product\/custom-counterweights\/crane-counterweights\/\">crane<\/a>, the capacity chart sets the limit. <a href=\"https:\/\/www.manitowoc.com\/media\/2186\/download\" target=\"_blank\" rel=\"noopener\">Manitowoc&#8217;s auxiliary counterweight folio for the 4100W Series-3<\/a> limits each 46,000 lb (20,866 kg) box to plus 700 lb (318 kg) and minus 0 lb, about +1.5% \/ \u22120.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The folio&#8217;s limit for a stack is the box limit added up: 8 boxes \u00d7 700 lb gives plus 5,600 lb on the 368,000 lb set. Divide a stack&#8217;s allowance by its piece count in the same way. The folio dates from 1995, is marked reference only and covers steel boxes filled with scrap iron and concrete. Use it to see how a builder writes a limit. Do not treat +1.5% as a target for a casting.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Elevator Counterweights<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">On a <a href=\"https:\/\/kurtfoundry.com\/product\/custom-counterweights\/elevator-counterweights\/\">traction elevator<\/a>, the design overbalance sets the limit. The elevator code puts the allowed maximum and minimum on a data plate. A weight error on the counterweight moves the overbalance by this amount:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Overbalance shift (percentage points) = counterweight weight error \u00f7 rated capacity \u00d7 100<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Forklift Counterweights<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">On a <a href=\"https:\/\/kurtfoundry.com\/product\/custom-counterweights\/forklift-counterweights\/\">forklift<\/a>, the truck maker sets the limit. <a href=\"https:\/\/www.osha.gov\/laws-regs\/regulations\/standardnumber\/1910\/1910.178\" target=\"_blank\" rel=\"noopener\">OSHA 1910.178<\/a> bars added counterweight unless the truck manufacturer approves it. A buyer replacing a weight therefore works to the maker&#8217;s figure. If you build the truck, run the method above against its rated capacity.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Tractor Ballast<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">On <a href=\"https:\/\/kurtfoundry.com\/product\/custom-counterweights\/tractor-counterweights\/\">tractor ballast<\/a>, <a href=\"https:\/\/eur-lex.europa.eu\/legal-content\/EN\/ALL\/?uri=CELEX%3A02015R0208-20161014\" target=\"_blank\" rel=\"noopener\">EU Regulation 2015\/208<\/a> requires the mass marked on ballast weights needed for EU type approval to be accurate to \u00b15%. The rule does not apply in the US.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">What Nominal Weight the Tolerance Applies To<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Measure the tolerance from the weight the machine needs, written on the drawing as a calculated weight. GB\/T 11351 also allows a nominal taken from weighed castings. That centers the tolerance on what the foundry poured, which suits a housing but can leave a counterweight short of the weight the machine needs.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Where the nominal is a calculated weight, write the density on the drawing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">State the condition of the part as well. Nominal weight under GB\/T 11351-89 includes <a href=\"https:\/\/kurtfoundry.com\/blog\/what-is-machining-allowance-sand-casting\/\">machining allowance<\/a>, so it is the as-cast weight. A counterweight works at its finished weight, so tie the tolerance on a machined piece to the finished weight. Say too whether the piece is weighed before or after paint.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Whether to Use a Plus-Minus or One-Sided Tolerance<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Use a one-sided tolerance, plus only and minus 0, when a light counterweight would fail the machine&#8217;s check and a slightly heavy one would not. Use plus-minus when both directions matter or when the figure only describes the weight.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The plus limit stays because too much counterweight is a fault too. A +5% \/ \u22120 limit is a 5% band, half the width of a \u00b15% limit. A process that holds a 10% band needs the whole band on the plus side, with the foundry aiming above nominal. Check that the machine accepts the heaviest piece.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Unequal limits are a third option, with more room above nominal than below. The 1989 edition of GB\/T 11351 allowed them.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How to Write the Tolerance on the Drawing or Order<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Write the tolerance as a note on the drawing, and repeat it on the purchase order. Put the acceptable weight on the RFQ too, as an actual weight where you have one.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The note needs four items:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Nominal weight<\/strong>: the figure in lb and kg, with the density if it is calculated.<\/li>\n\n\n\n<li><strong>Limits<\/strong>: the plus and the minus, as percentages or weights, even when one of them is 0.<\/li>\n\n\n\n<li><strong>Condition<\/strong>: as cast or finished, and before or after paint.<\/li>\n\n\n\n<li><strong>Piece and stack<\/strong>: the limit for each piece, plus a limit for the set if the pieces work as a stack.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">A 200 kg piece at \u00b15% could read: &#8220;Nominal finished weight 200 kg (441 lb), calculated at [density] g\/cm\u00b3, before paint. Tolerance \u00b15% per piece (190\u2013210 kg).&#8221;<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Write percentages rather than a bare grade. If an offshore foundry quotes &#8220;MT Grade 10&#8221;, or &#8220;MT Grade 10\/8&#8221; for unequal limits, ask which edition of GB\/T 11351 it means. Put the percentages on the order.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>Specify the tolerance as a percentage of a stated nominal weight, and start at about \u00b15% on a 100\u2013400 kg [&hellip;]<\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"closed","ping_status":"","sticky":false,"template":"","format":"standard","meta":{"_lmt_disableupdate":"","_lmt_disable":"","site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"default","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[24],"tags":[],"class_list":["post-3243","post","type-post","status-publish","format-standard","hentry","category-casting-design-patterns"],"modified_by":null,"_links":{"self":[{"href":"https:\/\/kurtfoundry.com\/fr\/wp-json\/wp\/v2\/posts\/3243","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/kurtfoundry.com\/fr\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/kurtfoundry.com\/fr\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/kurtfoundry.com\/fr\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/kurtfoundry.com\/fr\/wp-json\/wp\/v2\/comments?post=3243"}],"version-history":[{"count":3,"href":"https:\/\/kurtfoundry.com\/fr\/wp-json\/wp\/v2\/posts\/3243\/revisions"}],"predecessor-version":[{"id":3249,"href":"https:\/\/kurtfoundry.com\/fr\/wp-json\/wp\/v2\/posts\/3243\/revisions\/3249"}],"wp:attachment":[{"href":"https:\/\/kurtfoundry.com\/fr\/wp-json\/wp\/v2\/media?parent=3243"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/kurtfoundry.com\/fr\/wp-json\/wp\/v2\/categories?post=3243"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/kurtfoundry.com\/fr\/wp-json\/wp\/v2\/tags?post=3243"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}