Moving a part from gray iron to ductile iron leaves the machining stock and tolerance grades where they were, but the rigging changes: the casting needs risers whose necks freeze at the right moment, gates cut for an iron that forms dross, chills on some sections, and a shrink rule the foundry confirms for ductile iron instead of reusing the gray one. The property differences that prompt the switch are covered in our ductile iron vs gray cast iron comparison; this article covers only what happens to your tooling.
Plan for a pattern revision and a sampling run before production.
Shrink Allowance
A gray iron pattern’s shrink allowance should not be assumed to fit the same part in ductile iron. The ductile rule is the foundry’s own figure for the iron it pours, and a dimensional check of the first castings confirms it.
The usual gray iron rule is 1/8 inch per foot (0.125 in/ft) for castings up to 2 feet long. The pattern is made larger by:
Allowance (in) = dimension (in) × shrink rate (in/ft) ÷ 12
On an 18 in dimension of a gray iron casting, the 0.125 in/ft rule gives an allowance of 18 × 0.125 ÷ 12 = 0.1875 in, about 0.2 in.
Linear shrink moves with the iron’s matrix, so the foundry needs the grade and the section sizes before it sets the ductile rule. A pattern built to the gray rule can stay in service only if the first castings measure inside the drawing tolerance.
Risers
A ductile iron casting usually needs risers the gray iron casting did without, or larger ones.
Foundries size the new risers by modulus, the ratio of a section’s volume to its cooling surface area. A common starting ratio is:
Riser modulus : neck modulus : casting modulus = 1.2 : 1.1 : 1.0
That ratio is a starting point. A 2017 study on EN-GJS-400-18LT, cast in furan sand with exothermic risers, found the 1.2 riser-to-casting modulus ratio gave sound castings on 80 mm walls, while 40 mm walls needed a riser of almost 1.5 times the casting modulus plus chills. The new risers are checked in solidification simulation before the pattern is changed, then proven on sample castings. A firmer mold is part of feeding ductile iron as well.
Riser Necks
On a ductile iron casting the riser neck is sized to freeze off before the casting’s graphite expansion ends. In the 1.2 : 1.1 : 1.0 ratio, the neck modulus sits between the riser’s and the casting’s.
Gating
The gating system is normally redesigned, because ductile iron forms dross that a gray iron running system may not be laid out to trap. The new runners and gates are laid out for a calm, unbroken fill.
The gates that bring iron into the risers, called pressure gates, change too. They are cut wide and thin so they freeze early.
Chills
A ductile iron conversion needs chills where a riser cannot feed a section by itself: walls that run past a riser’s feeding distance, and heavy sections isolated from any riser. On the tooling, the chill locations go into the molding instructions, and sometimes onto the pattern or core box as seats.
Machining Stock and Core Prints
Neither the machining stock nor the core prints change because of the material. ISO 8062 gives gray iron and spheroidal-graphite (ductile) iron the same required machining allowance grades and the same casting tolerance grades in every sand process it lists:
| Sand process (ISO 8062:1994) | Machining allowance grade, gray iron | Machining allowance grade, ductile iron | Tolerance grade, gray iron | Tolerance grade, ductile iron |
|---|---|---|---|---|
| Hand-molded | F to H | F to H | CT11 to CT14 | CT11 to CT14 |
| Machine-molded and shell molding | E to G | E to G | CT8 to CT12 | CT8 to CT12 |
Those grades come from the 1994 edition, since replaced by ISO 8062-3. The current edition still lists the casting alloy among the details agreed on the drawing, so update the material callout and keep the stock as drawn.
There is no ductile-specific core print rule. A print is sized for the core it holds, and the core does not change with the iron, so the prints stay as they are unless the new risers or gates are placed over a cored area.
