On a sand-cast pump or gearbox housing, machine every surface that locates, seals or seats something, and leave the rest as cast. The machined list is bearing bores, seal bores, joint and flange faces, the seal chamber, wear-ring seats, and feet that bolt to a machined base. Walls, ribs and wet passages normally stay as they left the mold.
This applies to gray iron, ductile iron and steel housings cast in sand. An investment-cast housing starts with a smoother surface and closer dimensions, so its machined list can be shorter.
What Is an As-Cast Surface
An as-cast surface is the casting skin a housing carries when it leaves the mold, with no cutting done to it. The skin is rough and can hold cracks and porosity.
The skin also carries the marks of molding: draft on side walls, edges at parting lines, and cut-off and ground patches at gates. Shot blasting and the other ways to improve sand-cast surface finish make the skin cleaner and more even, but they do not bring it to a size on the drawing.
What Is a Machined Surface
A machined surface is one cut to a size, position and finish set on the drawing. Cutting removes the skin and places the surface accurately against the other machined features.
Boring can normally reach tolerance grade IT7, while milling normally holds IT10 to IT11. A precise bore or locating diameter is therefore bored.
On housings that get stress relief, the common order is rough machine, stress relieve, then finish machine. A housing also needs enough machining stock for the first cut to run below the skin.
The Difference Between As-Cast and Machined Surfaces
A machined surface is tighter, smoother and more repeatable than an as-cast surface, but it can expose porosity and it adds cost. The chart shows typical roughness by process, using the ranges in Machinery’s Handbook.
- Tolerance: A sand-cast dimension varies by millimetres, and a bored one by hundredths of a millimetre. On a 200 mm dimension, ISO 8062 casting tolerance grade CT10 (DCTG in the current edition) allows 4.0 mm in total, while a bored feature at grade 7 allows about 0.05 mm. Long-series machine-molded sand normally holds CT8 to CT10, and short-run green sand CT13 to CT15.
- Roughness: The finest typical sand-cast surface, 12.5 µm Ra, is still about twice as rough as the coarsest typical milled surface, 6.3 µm Ra.
- Datum repeatability: A machined face gives the same location on every part. An as-cast surface does not, so the first machining setup needs datum targets defined on the drawing. The foundry keeps parting lines and gate contacts off those targets.
- Exposed porosity: Cutting can open enclosed porosity to the surface or turn a blind pore into a through leak path.
- Cost: An as-cast surface adds no machining cost, while each machined surface does, and the cost climbs as the finish tightens.
How to Choose Which Surfaces to Machine
Machine a surface when something bolts to it, seals against it or runs in it, then set its finish by what touches it. A surface with none of those jobs stays as cast.
On a Gearbox Housing
On a gearbox housing, machine the bearing bores, oil-seal bores, joint faces, O-ring grooves, bolt seats and the feet. Leave interior walls, ribs, oil channels and exterior walls as cast.
- Bearing bores: Turning or fine boring is enough under general operating conditions. A bearing housing bore is finished to Ra 1.6 µm for small bearings and Ra 3.2 µm for large bearings. JTEKT’s table, the source of those figures, sets no size line between small and large, so confirm the finish with your bearing maker. Grind the seat only when the bearing needs minimum vibration and noise or runs under severe conditions.
- Oil-seal bores: ISO 6194-1 recommends an H8 housing bore for a radial shaft seal at Ra 1.6 to 3.2 µm.
- Gasketed joint faces: Mill them flat and stop at a moderate finish, because a smoother face lets a soft gasket creep. For a non-circular face such as a gear case joint, Garlock recommends 125 to 250 µin (3.2 to 6.3 µm) RMS with a multi-directional lay.
- Joints with anaerobic sealant: Flatness and gap matter more here than a stated Ra. Henkel’s white paper on Loctite 518 gives 0.1 mm over a 400 mm length as an example flatness limit for anaerobic flange sealants.
- O-ring grooves: Seal makers differ here. Parker’s O-Ring Handbook sets 32 µin (0.8 µm) maximum on static sealing surfaces for liquids, and the ERIKS manual accepts 64 to 125 RMS on static grooves. Use the figure from the maker of the O-ring you fit.
- Bolt seats: Spot-face them so the bolt head sits square.
- Feet: In our judgment, machine them when the unit bolts to a machined base, because a rough foot on a flat base still makes uneven contact. Where feet stay as cast, shim them so bolting down does not distort the housing.
On a Pump Housing
On a pump casing, machine the seal chamber, wear-ring seats, bearing bores, alignment fits, nozzle flange faces and the feet. Leave the volute and side-chamber walls as cast.
- Seal chamber: Machine the bore and the face. Flowserve’s CPM PX cartridge seal instructions ask for Ra 3.2 µm or better on the bore and Ra 1.6 µm or better on the face. They also ask for the face to be square to the shaft within 0.0005 mm/mm of chamber bore TIR. Those figures belong to that seal, so check them against the instructions for the seal you fit.
- Wear-ring seats: Bore them, because the case ring is a press fit. The usual fit a pump repair restores between case ring and casing is 0.002 to 0.003 in interference.
- Bearing bores: Use the same finishes as on a gearbox housing, Ra 1.6 µm for small bearings and Ra 3.2 µm for large bearings.
- Alignment fits: Machine the fits between the case and the heads, suction cover and bearing housing. Pump repair holds these alignment fits to 0.004 in maximum clearance.
- Nozzle flange faces: Machine them. MSS SP-6 allows gray and ductile iron faces up to 250 µin (6.3 µm) Ra non-serrated. For serrated steel faces it asks for a 125 to 250 µin (3.2 to 6.3 µm) Ra result. The standard is written for pipe flanges and the end flanges of valves and fittings and does not name pumps, so treat it as a guide and follow the pump’s purchase specification where it states a finish.
- Feet: Apply the same judgment as on a gearbox housing.
